Free Shipping Order Over $50
About the Product
This banger is made for dab rigs with a 45-degree angled joint. Its beveled edge and full-weld build offer durability and a great seal with carb caps.
The Honeysuckle Bevel 45° Degree Banger is the perfect choice for your angled dab rig. We designed it with a 45-degree neck, so the bucket sits level to prevent spills and heat evenly. Made from 100% quartz, its seamless full-weld construction offers better durability and heat flow than standard bangers. The beveled top edge creates a tight seal with your carb cap, a detail that improves airflow and vapor, helping you get more flavor from your dabs.
Is This 45° Banger Right For You?
Check this list to see if our Honeysuckle Bevel 45° is the right fit for your setup.
- Your rig has an angled joint: We made this banger for rigs with a joint set at a 45-degree angle.
- You want a better carb cap seal: The beveled edge provides a tight seal, especially with bubble and directional caps.
- Durability is a priority: Its seamless full-weld design is much stronger than typical bangers and resists heat stress.
- You like standard bucket sizes: The 25mm outer diameter is a great size for most dabs.
- You have a rig with a female joint: This banger comes in 14mm or 18mm male sizes to fit common rigs.
- You value quick heat-up times: The 2.5mm walls heat quickly but still hold heat well for a full session.
Product Specifications
Every detail of our Honeysuckle Bevel helps its performance. This table explains what each spec means for you.
| Specification | Value | Benefit |
|---|---|---|
| Material | 100% Fused Quartz | Offers great heat retention, durability, and a clean flavor. |
| Neck Angle | 45 Degrees | Keeps the bucket level on angled rigs to prevent spills and burning. |
| Bucket Diameter | 25mm (Outer) | Provides a versatile surface for a wide range of dab sizes. |
| Wall Thickness | 2.5mm | Balances quick heating with good heat retention for efficient use. |
| Top Edge | Beveled | Creates a tight seal with carb caps to maximize vapor and flavor. |
| Weld Type | Seamless Full Weld | Gives you maximum durability at the joint to prevent cracks and improve heat transfer. |
Which Joint Size Should I Pick?
Choosing the right joint is key for a good fit. We offer this banger in the two most common dab rig sizes. Measure your rig's joint to see which one you need.
- 14mm Male: Pick this size if your rig has a 14mm female joint. It's the most common size.
- 18mm Male: Pick this size if your rig has a larger 18mm female joint.
Both sizes have a frosted joint for a secure, airtight connection.
What Features Make This Banger Stand Out?
Three key design choices help our Honeysuckle Bevel Banger perform so well.
Why Choose A Beveled Edge Over A Flat Top?
A beveled edge is angled so a bubble or directional carb cap can sit securely inside the rim, creating a near-perfect seal. This stops vapor from escaping and directs airflow right onto your concentrates. Flat tops can leak air, wasting vapor and material.
What Is The Benefit Of A Seamless Full Weld?
With a seamless full weld, the bucket and neck are fused into one solid piece of quartz. This makes the joint much stronger and less likely to break from drops or heat. It also helps heat travel more efficiently from the neck to the bucket.
When Do You Need A 45-Degree Banger?
You need a 45-degree banger if your dab rig has an angled joint. A 90-degree banger would tilt, heating unevenly and spilling your concentrate. A 45-degree banger keeps the dabbing surface flat for the best results.
How To Use Your 45 Degree Banger For A Perfect Session
Follow these steps to get the best performance and longest life from your new Honeysuckle Banger.
- Attach to Rig: Fit the banger securely into the female joint on your angled rig.
- Heat the Banger: Use a torch to heat the bottom and sides of the bucket evenly for about 20-30 seconds. Do not heat the joint.
- Cool Down: Wait 40-60 seconds for the banger to cool. The right temperature depends on your dabs and preference.
- Apply Concentrate: Use a dab tool to place your material on the bucket floor.
- Cap and Inhale: Place a carb cap on the top and inhale slowly from the rig's mouthpiece.
- Clean Immediately: After your session, use a cotton swab to wipe out any residue while the banger is still warm. This prevents buildup.
What Are My Options? Under $50 Quartz Bangers Compared
Our Honeysuckle 45° is a specialized banger. Here is how it compares to other options in a similar price range.
| Feature | Honeysuckle Bevel 45° (Black Line) | Honeysuckle Bevel 90° | Standard Flat Top 90° | Honeysuckle Bevel 45° (Yellow Line) |
|---|---|---|---|---|
| Best For | Angled Rigs | Standard 90° Rigs | Budget / Simplicity | Angled Rigs (Thicker Quartz) |
| Top Edge | Beveled | Beveled | Flat | Beveled |
| Wall Thickness | 2.5mm | 2.5mm | 2mm | 3mm (Longer Heat Retention) |
| Carb Cap Seal | Excellent | Excellent | Good | Excellent |
How Do I Care For My Quartz Banger?
Proper care helps your quartz banger last a long time and provide pure flavor. The most important step is to clean it after every use. While the banger is still warm, use a dry cotton swab to wipe up any leftover oil. For stubborn spots, use a swab with isopropyl alcohol.
To avoid cracks, do not expose the banger to sudden temperature changes, like running it under cold water when hot. For a deep clean, soak the banger in an isopropyl solution for several hours. Then, rinse it with warm water and let it dry completely before your next use. This prevents blackening and buildup.
Complete Your Setup
A great banger works even better with the right accessories. Complete your setup with these essentials.
FAQ
What Is The 45°-Degree Terp Slurper For?
Since A Terp Slurper Is Different From A Traditional Style Banger, What Is The Best Temp For It?
- Choosing a selection results in a full page refresh.
!